Same-day shipping before 3PM CST · 35,000+ OEM Parts · Texas CMBL & SAM.gov Registered · Government POs Accepted

Menu

Home Shop All Account Cart
OEM Carrier Pressure Switch 22#CLS 7#OPN 50
Carrier

OEM Carrier Pressure Switch 22#CLS 7#OPN 50" for PH10JA036000AEAA

SKU: CARRIE-PH10JA036000AEAA-PRESSURE_SWITCH-HK02ZB038 Brand: Carrier
Guaranteed to fit PH10JA036000AEAA — or your money back. Terms

OEM Guaranteed

Same-Day Ship

30-Day Returns

Secure Checkout

Texas CMBL #19328542014
SAM.gov Registered
Govt POs Accepted

OEM Carrier Pressure Switch HK02ZB038 — 22#CLS / 7#OPN, 50" Leads — for Model PH10JA036000AEAA

This is the factory OEM replacement pressure switch (part number HK02ZB038) for the Carrier PH10JA036000AEAA packaged heat pump unit. The pressure switch is a critical safety component in the inducer/combustion circuit — it monitors negative pressure produced by the draft inducer motor and closes to signal the control board that proper airflow is established before allowing ignition to proceed. When this switch fails, the furnace or heat pump's gas section will lock out before ignition, the inducer will run but the system will not progress to the heating cycle, and you may see a diagnostic fault code pointing to an open pressure switch circuit.

  • Specs: Closing setpoint 22" W.C. | Opening setpoint 7" W.C. | 50" wire leads | Single-port hose connection | Factory-matched OEM switching tolerance
  • OEM vs Generic: This is a genuine Carrier OEM part (HK02ZB038) manufactured to exact factory W.C. setpoints. Aftermarket pressure switches frequently carry wider switching tolerances that can cause nuisance lockouts or, worse, allow ignition under marginal draft conditions — a potential safety concern.
  • Install difficulty: 2/5 — Straightforward swap. Turn off power at the disconnect and gas at the shutoff before beginning. Tools needed: 1/4" nut driver, needle-nose pliers, and a short length of replacement hose tubing (if existing hose is cracked). Photograph the hose routing and wire connections before removing the old switch.
  • Warranty: 1-year OEM manufacturer warranty against defects. Ships same business day from our warehouse when ordered before 3 PM local time.

Compatibility: Engineered and factory-specified for the Carrier PH10JA036000AEAA 3-ton packaged heat pump unit. Always verify the W.C. rating printed on your existing pressure switch or unit data plate before ordering — multiple pressure switch ratings are used across the PH10JA series depending on configuration. Our fitment team is available to confirm compatibility before you order. In stock — order now for same-day shipping.

Shipping Information

  • Orders placed before 3PM CST ship same business day
  • Standard delivery: 2-5 business days
  • Express shipping available at checkout
  • Free shipping on orders over $99
  • Tracking number emailed upon shipment

Return Policy

  • 30-day returns on unused parts in original packaging
  • Electrical parts (capacitors, contactors, control boards) are final sale once installed
  • Email info@nationalhvacparts.com to initiate a return
  • Refunds processed within 5-7 business days

Frequently Asked Questions

Does this Pressure Switch fit my Carrier PH10JA036000AEAA?
Yes. This is the factory-specified OEM pressure switch for the Carrier PH10JA036000AEAA. It is a direct drop-in replacement that fits without modification. Always verify the model number on your equipment nameplate before ordering.
How do I replace the pressure switch on my Carrier PH10JA036000AEAA?
Difficulty: Medium (20–30 min)
Step 1: Turn off power. Step 2: Locate pressure switch near draft inducer. Step 3: Note tubing orientation. Step 4: Disconnect tubing and wires. Step 5: Remove screw, install new switch. Step 6: Reconnect tubing and wires, restore power.
My furnace shows a pressure switch error. What do I replace?
Furnace LED showing pressure switch error = switch not detecting draft inducer airflow. Try first: clear the rubber tubing to the switch (often clogged with condensation). If problem persists, replace the pressure switch.
Is this pressure switch compatible with Bryant or Payne too?
Many Carrier parts are cross-compatible with Bryant and Payne since all three brands are manufactured by Carrier Global Corporation. The same physical part is often used across brand labels with different model numbers. To verify: check your Bryant or Payne equipment service manual for cross-compatible part numbers, or email info@nationalhvacparts.com with your model number.
Should I use OEM or aftermarket for my Carrier pressure switch?
OEM recommended for reliability and warranty compatibility. OEM parts match exact factory specifications for proper fit, performance, and safety. While aftermarket alternatives cost less upfront, the risk of improper fit and reduced lifespan usually makes OEM the better value long-term.
How fast does National HVAC Parts ship?
Orders placed before 3:00 PM CST ship the same business day. Standard delivery is 2–5 business days anywhere in the continental United States. Express shipping available at checkout. We ship from Houston, TX to all 50 states. 30-day return policy on all parts.
Home Shop Search Account Cart
Fitment Guaranteed
MR
Mike Rivera
HVAC Parts Specialist — Online