What igniter fits my ICP furnace?

The correct replacement for ICP model WFMR110C066A1 — Furnace HSI | Ships Today is this exact part. It is the factory-specified replacement with exact OEM specifications. Using a part with different specifications can cause equipment damage or void your warranty. You can verify this by checking the data plate on your ICP equipment which lists the model number WFMR110C066A1 — Furnace HSI | Ships Today.

My furnace will not ignite. What part is bad?

A furnace that will not ignite after the draft inducer runs typically has a failed igniter. The hot surface igniter should glow bright orange within 60 seconds. If it does not glow at all, it is cracked or burned out. If it glows weakly, it is degrading and should be replaced preventively. Average lifespan: 3 to 7 years.

ICP

ICP Hot Surface Igniter for WFMR110C066A1 — Furnace HSI | Ships Today

Name: ICP Hot Surface Igniter for WFMR110C066A1 — Furnace HSI | Ships Today
Brand: ICP
SKU: 1176919
Price: 50.70 USD
Availability: InStock

SKU: 1176919 Brand: ICP

OEM Guaranteed

Same-Day Ship

30-Day Returns

Secure Checkout

Texas CMBL #19328542014

SAM.gov Registered

Govt POs Accepted

Overview

This genuine OEM hot surface igniter (part number 1176919) is the ignition source for the ICP / Tempstar / Heil model WFMR110C066A1 furnace. On each heat call the board energizes the igniter, which glows red-hot to ignite the gas at the burners. Hot surface igniters are brittle and degrade with every cycle — a cracked or worn element is one of the most common causes of no-heat calls. This listing pairs the igniter with its related snap-fit gas valve hardware (part number 1176929, VALVE N HSI SNAP WR 36J24618) referenced for the same ignition assembly.

Specifications

Spec	Value
Part Number	1176919
Related Part	1176929 (Valve / HSI snap, 36J24618)
Type	Hot Surface Igniter (HSI)
Brand	ICP (Tempstar / Heil)
Voltage	120V
Application	Gas Furnace Ignition
Fit	OEM Direct Replacement

Compatibility

Direct OEM replacement for ICP, Tempstar, Heil, Comfortmaker, and related family gas furnaces using model WFMR110C066A1. Handle the silicon-carbide element only by its ceramic base — skin oils shorten igniter life.

Installation Guide

Safety First — Disconnect power at the furnace switch and breaker, then verify zero voltage with a multimeter.
Access — Remove the burner compartment service panel.
Document — Photograph the igniter position, bracket, and wire routing before disconnecting.
Remove — Unplug the igniter connector, remove the mounting screw, and carefully withdraw the old igniter without touching the element.
Install — Mount the new igniter so the element sits in the correct flame path, then reconnect the lead per your photo. Do not touch the element with bare fingers.
Test — Restore power and confirm the igniter glows and lights the burners on a heat call.

Signs You Need a Replacement

Furnace clicks and tries to fire but produces no flame
Visible crack, hot spot, or broken silicon-carbide element
Igniter no longer glows during the ignition sequence
Repeated ignition-failure lockouts on the control board

Shipping & Returns

Ships same day before 3 PM CST. 30-day returns. Backed by the National HVAC Parts fitment guarantee.

Shipping Information

Orders placed before 3PM CST ship same business day
Standard delivery: 2-5 business days
Express shipping available at checkout
Free shipping on orders over $75
Tracking number emailed upon shipment

Return Policy

30-day returns on unused parts in original packaging
Electrical parts (capacitors, contactors, control boards) are final sale once installed
Email info@nationalhvacparts.com to initiate a return
Refunds processed within 5-7 business days

ICP Hot Surface Igniter for WFMR...

$50.70

Frequently Asked Questions

Does this Igniter fit my ICP WFMR110C066A1 — Furnace HSI | Ships Today?

Yes. This is the factory-specified OEM igniter for the ICP WFMR110C066A1 — Furnace HSI | Ships Today. It is a direct drop-in replacement that fits without modification. Always verify the model number on your equipment nameplate before ordering.

How do I replace the igniter on my ICP WFMR110C066A1 — Furnace HSI | Ships Today?

Difficulty: Medium (20–30 min)
Step 1: Turn off power and gas. Step 2: Open furnace panel. Step 3: Locate igniter near burners. Step 4: Disconnect two-wire plug. Step 5: Remove mounting screw. Step 6: Install new igniter — do NOT touch element with fingers. Step 7: Reconnect, close panel, restore power/gas.

My furnace won’t ignite. What part is bad?

Furnace won’t ignite after the draft inducer runs = failed igniter. The hot surface igniter should glow bright orange within 60 seconds. No glow = cracked/burned out. Weak glow = degrading. Average lifespan: 3–7 years. Replacement: $15–$40 DIY.

Is this igniter compatible with Bryant or Payne too?

Many ICP parts are cross-compatible with Bryant and Payne since all three brands are manufactured by Carrier Global Corporation. The same physical part is often used across brand labels with different model numbers. To verify: check your Bryant or Payne equipment service manual for cross-compatible part numbers, or email info@nationalhvacparts.com with your model number.

Should I use OEM or aftermarket for my ICP igniter?

OEM recommended for reliability and warranty compatibility. OEM parts match exact factory specifications for proper fit, performance, and safety. While aftermarket alternatives cost less upfront, the risk of improper fit and reduced lifespan usually makes OEM the better value long-term.

How fast does National HVAC Parts ship?

Orders placed before 3:00 PM CST ship the same business day. Standard delivery is 2–5 business days anywhere in the continental United States. Express shipping available at checkout. We ship from Houston, TX to all 50 states. 30-day return policy on all parts.

Menu