{"product_id":"icp-hot-surface-igniter-for-rgs120hdba0agaa-includes-igniter-wiring-kit-ships-today","title":"ICP Hot Surface Igniter for RGS120HDBA0AGAA — Includes Igniter Wiring Kit | Ships Today","description":"\u003ch3\u003eOverview\u003c\/h3\u003e\n\u003cp\u003eThe OEM hot surface igniter (ICP part 1171306) is the ignition source for the ICP\/Heil\/Tempstar RGS120HDBA0AGAA gas furnace. On each call for heat, the control board energizes this igniter; it glows to roughly 2,000°F to light the burner gas. Hot surface igniters are the single most common failure point in modern gas furnaces — the silicon-carbide or silicon-nitride element is brittle and degrades with every heating cycle. When it cracks or burns out, the furnace blower may run but the burners never light, leaving you with no heat. This OEM listing ships with the matching igniter wiring kit (part 1188370) so you have the correct harness and connector for a clean, code-correct installation.\u003c\/p\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSpec\u003c\/th\u003e\n\u003cth\u003eValue\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eOEM Part Number\u003c\/td\u003e\n\u003ctd\u003e1171306 (igniter)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eIncluded Kit\u003c\/td\u003e\n\u003ctd\u003e1188370 (wiring kit, igniter)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eType\u003c\/td\u003e\n\u003ctd\u003eHot Surface Igniter\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eICP \/ Heil \/ Tempstar\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eApplication\u003c\/td\u003e\n\u003ctd\u003eGas furnace burner ignition\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFitment\u003c\/td\u003e\n\u003ctd\u003eOEM direct replacement\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eCompatibility\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement for the ICP\/Heil\/Tempstar RGS120HDBA0AGAA furnace and other ICP-family models using the same igniter assembly. Because it ships with the OEM wiring kit, it matches the factory connector — no splicing or universal adapters required.\u003c\/p\u003e\n\n\u003ch3\u003eInstallation Guide\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eSafety First\u003c\/strong\u003e — Disconnect power at the furnace switch and breaker, and shut off the gas. Verify zero voltage with a multimeter before touching wiring.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAccess\u003c\/strong\u003e — Remove the furnace burner\/control compartment service panel.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDocument\u003c\/strong\u003e — Photograph the igniter wiring and bracket position before disconnecting.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRemove\u003c\/strong\u003e — Unplug the igniter connector, remove the mounting screw, and lift the old igniter out without touching the element. Handle the new igniter by its ceramic base only — skin oil shortens element life.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstall\u003c\/strong\u003e — Mount the new igniter in the same orientation, route and plug in the new wiring kit, and confirm the element sits in the burner flame path per the factory photo.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTest\u003c\/strong\u003e — Restore gas and power, then run a heat cycle and confirm the igniter glows, the burners light, and flame is established cleanly.\u003c\/li\u003e\n\u003c\/ol\u003e\n\n\u003ch3\u003eSigns You Need a Replacement\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eFurnace runs the inducer and blower but burners never ignite (no heat).\u003c\/li\u003e\n\u003cli\u003eVisible cracks, blistering, or broken element on the old igniter.\u003c\/li\u003e\n\u003cli\u003eIgniter glows weakly or not at all during a heat call.\u003c\/li\u003e\n\u003cli\u003eControl board lockout \/ ignition-fault flash code after several failed tries.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eShipping \u0026amp; Returns\u003c\/h3\u003e\n\u003cp\u003eShips same day on orders placed before 3 PM CST. 30-day returns. Backed by the National HVAC Parts fitment guarantee.\u003c\/p\u003e","brand":"ICP","offers":[{"title":"OEM","offer_id":63027605569907,"sku":"1171306","price":44.2,"currency_code":"USD","in_stock":true},{"title":"Generic","offer_id":63047629701491,"sku":"1171306-GEN","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/1190\/5395\/files\/nhvac-igniter-silicon-carbide-1171306_a4977cad-5309-4ca1-bc67-f743ea5b0b92.jpg?v=1782892196","url":"https:\/\/nationalhvacparts.com\/products\/icp-hot-surface-igniter-for-rgs120hdba0agaa-includes-igniter-wiring-kit-ships-today","provider":"National HVAC Parts","version":"1.0","type":"link"}