{"product_id":"icp-hot-surface-igniter-for-rgs102hfab0aaa-furnace-silicon-nitride-120v-ships-today","title":"ICP Hot Surface Igniter for RGS102HFAB0AAA Furnace – Silicon Nitride 120V | Ships Today","description":"\u003ch3\u003eOverview\u003c\/h3\u003e\u003cp\u003eThis OEM hot surface igniter (part #1171306) is the ignition source for the ICP\/Heil\/Tempstar RGS102HFAB0AAA gas furnace. When the thermostat calls for heat, the furnace control board sends 120V to this igniter, which glows red-hot and lights the burners. It ships complete with the OEM igniter wiring kit (part #1188370) for a clean, no-splice installation. Igniters are a high-wear part — repeated heating and cooling cycles eventually crack the element. A failed igniter is one of the most common causes of \"no heat\" calls: the inducer runs, the gas valve waits, but the burners never light and the furnace locks out.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSpec\u003c\/th\u003e\n\u003cth\u003eValue\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003ePart Number\u003c\/td\u003e\n\u003ctd\u003e1171306 (igniter), 1188370 (wiring kit)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eType\u003c\/td\u003e\n\u003ctd\u003eHot Surface Igniter\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eICP \/ Heil \/ Tempstar\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eVoltage\u003c\/td\u003e\n\u003ctd\u003e120V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eElement\u003c\/td\u003e\n\u003ctd\u003eSilicon nitride\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFitment\u003c\/td\u003e\n\u003ctd\u003eOEM\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch3\u003eCompatibility\u003c\/h3\u003e\u003cp\u003eEngineered as a direct fit for the ICP\/Heil\/Tempstar RGS102HFAB0AAA gas furnace and shared-platform ICP brand models (Comfortmaker, Arcoaire, Day \u0026amp; Night). Always confirm the part number on your existing igniter before ordering.\u003c\/p\u003e\u003ch3\u003eInstallation Guide\u003c\/h3\u003e\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eSafety First\u003c\/strong\u003e – Shut off gas and disconnect power at the furnace switch; verify zero voltage with a multimeter.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAccess\u003c\/strong\u003e – Remove the furnace burner\/control access panel.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDocument\u003c\/strong\u003e – Photograph the igniter bracket position and the wiring harness routing before disconnecting.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRemove\u003c\/strong\u003e – Unplug the igniter connector, remove the mounting screw, and lift out the old igniter. Handle the new element by the ceramic base only — skin oils shorten igniter life.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstall\u003c\/strong\u003e – Mount the new igniter, secure the bracket, and connect the supplied OEM wiring kit per your photo.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTest\u003c\/strong\u003e – Restore gas and power, start a heat cycle, and confirm the igniter glows and burners light within a few seconds.\u003c\/li\u003e\n\u003c\/ol\u003e\u003ch3\u003eSigns You Need a Replacement\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eFurnace inducer runs but burners never ignite (no heat)\u003c\/li\u003e\n\u003cli\u003eVisible crack or break in the ceramic element\u003c\/li\u003e\n\u003cli\u003eIgniter glows weakly or not at all during a call for heat\u003c\/li\u003e\n\u003cli\u003eFurnace lights out and short-cycles or hard-locks on ignition fault codes\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eShipping \u0026amp; Returns\u003c\/h3\u003e\u003cp\u003eShips same day before 3 PM CST. 30-day returns. Backed by the National HVAC Parts fitment guarantee.\u003c\/p\u003e","brand":"ICP","offers":[{"title":"OEM","offer_id":63027645776243,"sku":"1171306","price":41.6,"currency_code":"USD","in_stock":true},{"title":"Generic","offer_id":63047627833715,"sku":"1171306-GEN","price":32.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/1190\/5395\/files\/nhvac-igniter-silicon-nitride-1171306_5823bebb-f4c9-4c97-80ec-c78f1f1ed50f.jpg?v=1782892147","url":"https:\/\/nationalhvacparts.com\/products\/icp-hot-surface-igniter-for-rgs102hfab0aaa-furnace-silicon-nitride-120v-ships-today","provider":"National HVAC Parts","version":"1.0","type":"link"}